Based in Enfield. Working across Adelaide and regional SA. 08 8151 1040

Electrical, mechanical and electronics engineering in Adelaide

VD Fire Safety and Electrical Solutions Pty Ltd designs, installs and commissions electrical, mechanical and electronic systems for commercial and industrial sites across Adelaide, from power distribution and ventilation to PLC automation and fire panel programming. Every project is scoped and quoted on its own requirements.

What VD’s engineering line does

VD Fire & Electrical is best known for fire safety and electrical compliance servicing. The same company, VD Fire Safety and Electrical Solutions Pty Ltd, also runs an electrical and electronics engineering line for commercial and industrial clients across Adelaide.

The work falls into three areas, each with its own page, alongside fire safety design and commissioning.

Electrical design and installation

Industrial and commercial electrical installations, power distribution and control system design, electrical system upgrades and performance monitoring, and electrical safety inspections and risk assessments. Electrical installation work is carried out through our licensed electrical contractor. See electrical design.

Automation, controls and electronics

PLC programming and industrial automation, fire safety system integration with building plant, communication system design and installation, embedded systems development, electronics testing and commissioning, and technical documentation and support. See automation and controls.

Mechanical engineering

Mechanical services for commercial and industrial buildings: ventilation, air conditioning and exhaust systems, and the fire and smoke control side of mechanical plant, such as fire mode shutdown and fire dampers. See mechanical engineering.

Fire alarm and indicator panel programming

We program fire indicator panels after a fit-out, an extension or a change of use: adding and removing detectors and zones, updating zone text, and setting up the outputs that shut down air handling or release doors held open. See fire alarm and detection testing.

Fire engineering, through our partner

Some buildings need a fire engineer: a performance solution for a building approval, a fire engineering report, or advice on a change of use. We arrange this through a partner fire safety engineer and coordinate their work with ours, so the design, the installation, the testing and the Form 2 sign off fit together. The fire engineering itself is done and signed by the partner, not by our own staff.

Who we work with

Our engineering clients are the people responsible for keeping a site running:

  • commercial building owners and facility managers
  • builders and principal contractors
  • industrial plant and warehouse operators
  • property managers of multi-residential complexes
  • operators of education, health and aged care buildings

How a project runs

  1. Scope. We visit the site, talk through what you need and review any existing drawings, single-line diagrams or control logic.
  2. Design. We prepare the design and documentation for your approval, sized to the job: a marked-up drawing for a small upgrade, a full design package for a new installation.
  3. Quote. You get a fixed quote, or a staged one for larger jobs, before any work starts.
  4. Install. Electrical installation work is carried out through our licensed electrical contractor.
  5. Test and commission. Every system is tested as a whole before handover, as well as component by component.
  6. Hand over. You get as-built documentation and ongoing technical support.

Fire safety design and commissioning

Alongside the electrical and electronics work, we offer fire safety design and commissioning for commercial and industrial buildings. Much of it is delivered through our fire safety services:

We do not prepare fire safety performance solutions. If your project needs one, your certifier can tell you what kind of practitioner to engage, and we can work with them on the electrical and commissioning side.

Why one contractor for electrical and fire

Electrical, controls and fire systems meet at the same points in a building: the switchboard, the fire indicator panel, the plant room and the lifts. When one team understands all three, there are fewer gaps at handover and fewer faults blamed on “the other contractor”.

Our qualifications

We hold a test and tag licence, and electrical installation work is carried out through our licensed electrical contractor. On the fire side we hold a CBS PGE fire plumbing licence, are FPAS accredited and are FPA Australia members. We carry public liability and professional indemnity cover of $20 million. Ask us about the qualifications of the team on your project.

Frequently asked questions

Is engineering a separate company from VD Fire & Electrical?
No. Engineering is a separate line of work, but it is the same company: VD Fire Safety and Electrical Solutions Pty Ltd. You deal with the same team, the same phone number and the same office in Enfield.
What kinds of sites do you work on?
Commercial and industrial sites: offices, factories, warehouses, retail, multi-residential complexes, and education, health and aged care buildings.
Do you prepare fire safety performance solutions?
Through our partner. Performance solutions and fire engineering reports are prepared and signed by a partner fire safety engineer, not by our own staff. We arrange the engagement and coordinate it with our own fire side work: evacuation plan drafting, fire system installation, testing and commissioning, maintaining essential safety provisions and the Form 2 and Form 3 documentation.
What qualifications does your engineering team hold?
Electrical installation work is carried out through our licensed electrical contractor, and we hold a test and tag licence. We carry public liability and professional indemnity cover of $20 million. Ask us about the qualifications of the team on your project.
Can you take on a project that is already partly built?
Yes. Upgrades, extensions and fault finding on existing installations are a large part of electrical and controls work. We start by surveying what is there and reviewing any existing drawings.
Call 08 8151 1040 Get a quote